SETAFLASH SERIES 3 CLOSED CUP TESTER

Series 3 in the cosmetics industry See Komatsu use the Series 3. The procedure for making SWS is included in the standard method of test. Do NOT use Auto mode. However Stanhope-Seta cannot accept responsibility for any omissions or errors. The manual flash test is carried out by pulling a lever which opens a shutter on the lid and dips the flame from the test jet through the shutter aperture into the vapour space above the sample. Setaflash Series 3 closed cup flash point tester provides fast and reliable flash point results and requires you to have minimum expertise. A “popping” sound may be heard when the flame is dipped into the vapour space.

Reproduction in whole or part is strictly prohibited, except with the written consent of Stanhope-Seta, and then only on the condition that this notice is included in any such reproduction. Stanhope-Seta Ltd reserve the right to change or alter the specifications, operating procedures etc detailed within this document. The Series 3 Flash Point Tester is lightweight and suitable for mobile use when you operate using the optional 12 volt power supply adaptor. All Closed Cup testers feature automatic flash detection. Tests on liquid paints excluding chemical tests. Model because it has a peltier cell cooling system built in.

When momentarily pressed then released, the flash detector probe is reset ready for the next test. Calibration and verification equipment available.

Leave the flame to stabilise for about 30 seconds before final adjustment to flame size.

Stanhope-Seta – Setaflash Series 3 Closed Cup Flash Point Tester – John Morris

The major items are: The power supply voltage and frequency are also shown. When pressed and held down, the control knob may be rotated to either select the mode of operation, or set the time interval for the test. Determination of flash no-flash and flash point. To use the coolant module, proceed as follows refer to the illustrations: Series 3 in the cosmetics industry See Komatsu use the Series 3 See detailed specifications Available accessories Request a quotation Download a brochure pdf More products in this subcategory.

Automatic Sample Cup material Aluminium Operational ambient temperature range: The serial number and software version must be quoted in any technical query, or when ordering accessories and spare parts. A manual reset button is situated on the rear panel to restore power after the assembly has cooled to a safe temperature.

  BOX CINEMA ITAQUERA FILMES EM CARTAZ

REPAIR 1 If the instrument is to be returned to our factory for repair, ensure that it is adequately packed for the intended method of transport. An automatic flash detector reduces the chance of you misinterpreting the test result and enhances repeatability. The Setaflash Series 3 Flash Point Testers are calibrated for temperature using a single point method.

An audible prompt sounds when a flash is achieved.

Setaflash Series 3 Flash Point Tester

All power is disconnected from the instrument 5 How do I verify the correct operation of the instrument? The procedure is carried out via the panel controls and requires a reference thermometer and some thermo-conductive paste. Turn the canister the correct way round brass insert uppermost and re-insert it into the holder. When the test flame size cannot be set correctly or there is no liquid visible in the transparent part of the gas canister 16 How many tests can I do with a full gas canister?

The version number will not be displayed on instruments with pre version 2 software installed. To access the fuse, prise the fuse holder open with a screwdriver blade. Run a test using a certified flash point reference material 6 What should I do if the shutter assembly sticks?

The control panel comprises two push buttons, a single control knob, and a display. Adjust if necessary by turning the Pinch Valve. A precision platinum resistance thermometer measures the temperature of the cup, providing data for the display and the heater controller. However Stanhope-Seta cannot accept responsibility for any omissions or errors.

These are available from Stanhope-Seta 13 Should I turn the instrument off at the end of a day’s use? For easy record keeping the instrument storestest results which can be saved and transferred via a USB port. Integral timer for standard 1 and 2 minute tests, and up to 30 minutes Audible and visual indication Temperature measurement: Temperature control is achieved by a digital heater controller.

Elcometer /1 Setaflash ‘Series 3’ Closed Cup Tester

Copyright Stanhope—Seta Limited Stanhope-Seta Ltd reserve the right to change or alter the specifications, operating procedures etc detailed within this document. Issue K 10 Jun 24 Pubn No: Remove all traces of the solvent 7 Should Eetaflash use this equipment in a fume cupboard?

  CHARACTERISTICS OF STRATOSPHERE-TROPOSPHERE EXCHANGE DURING THE MEIYU SEASON

A 2-line alphanumeric display shows cup temperature, timer settings, sample size, calibration information, and whether a flash has occurred.

Issue K 10 Jun 6 Pubn No: Release Rotate the Control Knob …. An Open Cup tester, Modelis also available.

The operating principle of Setaflash Series 3 Testers is that ckosed cup, containing the sample to be tested, is electrically heated to a user set test temperature, then a manual flash test is carried out. Model 11 Which closed cup model should I use for tests at close to ambient temperature?

Series 3 in the cosmetics industry See Komatsu use the Series 3. Models, or 10 Which model should Seyaflash use for corrosive samples? The reset button is mounted on the rear of the tester. Check that the lid is flat and that the hinge is not strained. Issue K 10 Jun Thermometer T? Fup Series 3 closed cup flash point tester provides fast and reliable flash point results and requires you to have minimum expertise.

Stanhope Seta™ Setaflash™ Series 3 Closed Cup Flash Point Tester

Each unit is tested for electrical safety is then calibrated. If there is not sufficient adjustment, centralise the Control Valve, and adjust the Castellated Inner Wheel, then re-adjust the Control Valve. Setaflash Series 3 has a very simple user interface with colour digital display and touchscreen icons which guide you through a straightforward testing process. The information contained in this publication is believed to be accurate and correct at the time of printing.

Issue K 10 Jun 2 Pubn No: This may result in some discolouration of the sample cup and surrounding area. Instruments with pre version 2 software are covered in publication number H0E dated 5 July This information must be quoted in any technical query, or when ordering seres and spare parts.